Tech Peak » How To Install Samsung Galaxy A515, A51 Black Original LCD & Touch Screen

How To Install Samsung Galaxy A515, A51 Black Original LCD & Touch Screen

by razsmiths
lcd phone parts, Cell phone parts, lcd screen replacement, Mobile Parts, phone lcd part, samsung parts,

Introduction

With this new method, you can now easily install the original black LCD & Touch Screen for Samsung Galaxy A515 and A51. This will help you to have a clear and bright display on your phone.

What You Will Need

To install your Samsung Galaxy A, you will need a few tools. Firstly, you will need a Phillips head screwdriver. Secondly, you will need a spudger. This is a tool that is used to help pry things open. Thirdly, you will need a suction cup. This is used to help remove the old LCD screen. Lastly, you will need the new LCD and touch screen.

Once you have the necessary tools, you can begin the installation process. First, use the Phillips head screwdriver to remove the screws on the back of the phone. Next, use the spudger to pry open the back panel. Be careful not to damage the board as you do this. Once the back panel is removed, you can see the battery and other internals of the phone.

Now, use the suction cup to remove the old LCD screen. Be careful not to damage the flex cable as you do this. Once the old screen is removed, you can carefully apply the new LCD and touch screen. Make sure that everything is connected adequately before reassembling your phone.

Following these steps should allow you to properly install your new Samsung Galaxy A LCD and Several kits are available online if you decide to go the DIY route. Be sure to do your research and choose a reputable brand. Once you have your equipment, follow the instructions carefully and take your time. It’s essential to avoid causing any further damage to the screen.

Step One: Remove the Back Cover

  1. Step One: Remove the Back Cover

Start by removing the back cover of your Samsung Galaxy A. This will give you access to the battery and SIM card slot. To remove the back cover, gently pry it off from the top or bottom of the phone.

  1. Step Two: Insert the Battery

Next, insert the battery into your phone. Make sure that the battery’s positive (+) side is facing up. Once the storm is in place, replace the back cover.

  1. Step Three: Insert the SIM Card

Now, insert the SIM card into your phone. The SIM card goes into the slot, which is under the back cover. Once the SIM card is in place, replace the back cover.

  1. Step Four: Power On Your Phone

Finally, power on your phone by pressing and holding the power button for a few seconds. Your phone should now be up and running!

Step Two: Remove the Battery

  1. Step Two: Remove the Battery

To install your new Samsung Galaxy A, A Black Original LCD & Touch Screen, you will need to remove the battery first. To do this, locate the battery door on the back of the phone and remove the screws holding it. Once the screws are removed, you should be able to slide the battery door off.

  1. Step Three: Remove the Back Cover

With the battery door removed, you will now be able to access the phone’s back cover. Begin by removing the screws that are holding it in place. Once all the screws are removed, you should be able to lift off the back cover carefully.

  1. Step Four: Remove the Old LCD & Touch Screen

You will now access the old LCD & Touch Screen assembly with the back cover removed. To remove it, disconnect the flex cable connecting it to the motherboard. Once disconnected, you should be able to lift it out of the phone carefully.

  1. Step Five: Install The New LCD & Touch Screen

Connect the flex cable to install your new Samsung Galaxy A, A Black Original LCD & Touch Screen. With this new method, you can now easily install the original black LCD & Touch Screen for Samsung Galaxy A515 and A51. This will help you to have a clear and bright display on your phone.

Step Three: Remove the SIM and SD Card Trays

Step Three: Remove the SIM and SD Card TraysUse a SIM eject tool or a paperclip to remove the tray from the top of the phoneIf you have an SD card in your phone, remove it from the tray and set it aside. Replace the SIM and SD card trays and push them back into place

Step Four: Separate the Frame from the LCD Screen

To protect your LCD screen, it is essential to remove the frame from around it. To do this, you will need to use a small screwdriver or a pry tool. Gently insert the screwdriver or pry tool into the seam between the frame and the LCD screen. Then, apply pressure to the device to separate the two pieces. Be careful not to use too much pressure, as this could damage the LCD screen.Once the frame has been removed, you can proceed to Step Five.

Step Five: Remove the Old LCD Screen

You will need to remove the old LCD screen to install your new Samsung Galaxy A, A Black Original LCD & Touch Screen lcd phone parts .

First, use a Phillips head screwdriver to remove the two screws that secure the phone’s back cover. Next, use a pry tool to remove the back cover gently. Be careful not to damage the back cover or the phone itself.

Once the back cover is removed, you will see the battery. Use a Phillips head screwdriver to remove the two screws that secure the battery. Gently lift the battery out of the phone and set it aside.

Now you will see the old LCD screen. Gently peel it away from the phone, careful not to damage any other components. Once it is removed, you can begin installing your new LCD screen.

Step Six: Install the New LCD Screen

  1. Step Six: Install the New LCD Screen

To install the new LCD screen, you’ll need to remove the old one first. Start by unplugging the cable that connects the old LCD screen to the main board. Then, drag the screws that hold the old LCD screen in place. Carefully lift out the old LCD screen and set it aside.

Next, take the new LCD screen and carefully insert it into the opening. Make sure that all of the connections are securely in place. Then, replace the screws that hold the LCD screen in place. Finally, reconnect the cable that connects the LCD screen to the main board samsung parts .

Step Seven: Reassemble Your Phone

The final step is to reassemble your phone. Make sure to put all the screws back and tighten them securely. Then, replace the back cover of your phone. Once you have done this, your phone should be as good as new!

Now, use the suction cup to remove the old LCD screen. Be careful not to damage the flex cable as you do this. Once the old screen is removed, you can carefully apply the new LCD and touch screen. Make sure that everything is connected adequately before reassembling your phone.

Conclusion

So there you have it — a quick guide on installing a Samsung Galaxy A515, A51 Black Original LCD & Touch Screen. We hope that this guide was helpful and that you successfully installed your new screen. If you have any questions or comments, please feel free to leave them below.

 

You may also like

Leave a Comment